CGI Windows & Doors Nationwide

CGI Windows & Doors: The Irvine Owner’s Guide

CGI windows and doors in Irvine typically run $4,500-$15,000 for full replacement and $400-$1,800 for component-level repair, with most hardware and sash parts available same-day through our verified supply chain. We stock and install CGI-compatible parts across the Estate, Sentinel, and Estate Collection series, matching OEM specs or sourcing equivalent-grade hardware when the factory part is back-ordered. Most Irvine homeowners first notice a problem when a window won’t stay open, a door sticks in the jamb, or they feel a draft along the sill despite the latch appearing closed.

Call (657) 227-2502

Which CGI Models This Applies To

CGI’s product lines break into three main series, and the part you need depends on which one is on your wall. The Estate Collection uses heavier extruded aluminum frames with stainless steel hardware rated for high-velocity wind zones, common in Irvine’s newer developments near Orchard Hills and Portola Springs where HOA design guidelines often mandate impact-rated assemblies. The Sentinel series is the mid-grade line with similar frame depths but different corner keys and weatherstrip profiles. The base Estate line uses lighter hardware and a distinct snap-in glazing bead that isn’t interchangeable with the Collection’s wedge-fit system.

To identify your series, check the etched code on the glass spacer or the stamp on the hinge barrel. Estate Collection hardware carries a “CGI-EC” prefix; Sentinel uses “CGI-S.” The critical compatibility gotcha in Irvine’s inland climate: the Estate Collection’s dual-fin weatherstrip, designed for Florida humidity cycling, can harden faster in Orange County’s dry heat and dust, so we spec a silicone-core replacement rather than OEM neoprene when we do the swap. OEM parts ship from CGI’s Florida facility in 5-10 business days; we maintain equivalent-grade hardware from Amesbury and Truth Hardware in our Irvine inventory for same-day resolution.

Signs Your CGI Windows & Doors Is Failing

• The sash drops or won’t hold position. This usually means the coil balance or pivot bar has worn flat. In Irvine’s hard water areas, mineral buildup in the balance shoe accelerates wear; we find this most often in homes near the Turtle Rock foothills where irrigation overspray hits lower windows.
• Visible daylight or air movement at the frame perimeter. The compression seal has taken a set and no longer rebounds. CGI’s original pile weatherstrip lasts 8-12 years in this climate; once it goes, the thermal performance drops before most owners notice the draft.
• The multipoint lock won’t engage or requires excessive force. The locking points have shifted out of alignment, often because the keepers have loosened from thermal cycling between Irvine’s 50°F winter mornings and 95°F summer afternoons.
• Condensation between glass panes. The insulating glass unit (IGU) seal has failed. This is not a hardware fix; the entire sash or IGU needs replacement. In south-facing CGI units, we see this at 10-14 years, earlier than north-facing installations.
• The door slab binds or scrapes the jamb. The hinge screws have wallowed out in the aluminum stile, or the sill cap has deformed from foot traffic and thermal expansion. Tightening the screws without addressing the stripped hole makes it worse.

Before

After

Replacement Cost & What’s Included

For CGI windows and doors in Irvine, component repair runs $400-$1,800 depending on what’s actually failed. A coil balance and pivot bar replacement on a standard double-hung is typically $400-$650. Full sash replacement with IGU on a 36×72 Estate Collection unit runs $1,200-$1,800 including removal, disposal, and re-caulking. Full window replacement across a typical Irvine home starts at $4,500 and ranges to $15,000 for whole-house Estate Collection with impact glass.

Every quote we write itemizes parts, labor, and disposal separately. Under Clause 1 of The Haven Standard, that written price is the price; no work starts until you have it in hand. Our 365-Day Done Right Promise covers the installation and hardware function; the glass itself carries the manufacturer’s warranty. We pull permits when the scope requires it, pass inspection, and you leave with a documented photo record of the completed work.

DIY or Call Us?

There’s a short list an owner can safely check. Verify the lock keeper screws are tight. Clean debris from the sill track with a vacuum and dry brush. Check if the window is simply unlocked (it happens more than you’d think). Beyond that, CGI’s aluminum extrusions and tempered glass assemblies carry real risk: a dropped sash can shatter, and the coil springs under tension can release suddenly.

We don’t recommend homeowner disassembly of balance systems, IGUs, or multipoint locks. The hardware is specific to the series, and using a generic replacement from a big-box store usually means it fits poorly and fails faster. If you’re unsure which series you have or whether the part is still available, call us at (657) 227-2502. We’ll identify it from photos or a brief site visit, and the estimate is free.

FAQs