Boral Fence Installation Nationwide

Boral Fence Installation: The Irvine Owner’s Guide

Boral fence installation in Irvine typically runs $3,500-$9,000 for a complete residential project, with most single-family homes in neighborhoods like Woodbridge and Northwood falling in the $5,500-$7,500 range depending on linear footage and site conditions. We stock Boral-compatible posts, rails, and infill panels for same-week scheduling, and we’ll put the installed price in writing before any crew loads a truck. Most Irvine owners first notice trouble when HOA inspection letters arrive citing leaning posts, cracked composite boards, or gate hardware that no longer latches square, often after one of our Santa Ana wind events or a wet winter that shifted the footing.

Call (657) 227-2502

Which Boral Models This Applies To

Boral’s fence line has moved through several naming conventions, and the part you need depends on when your original fence was sourced. The Boral TruExterior poly-ash fence boards, common in Irvine builds from 2012 to 2019, measure 5/8″ thick and run true 6″ face width, unlike the nominal sizing you’ll find at big-box retailers. Boral’s newer cellular PVC lines, including styles sold through select distributors after 2020, use a different rail clip system with 1-7/8″ pocket spacing that is not backward compatible. We carry both rail systems on our trucks, along with the stainless steel fasteners Boral specifies for coastal-zone installs, which matters in Irvine’s marine-influenced Climate Zone 3B where standard coated screws can fail within 36 months.

To identify your board: TruExterior carries a stamped date code and “Boral” branding on the back face; cellular PVC lines have a printed label with a SKU starting in BOR-PVC. If your fence was installed by a previous owner without records, we measure board thickness, rail pocket depth, and post spacing on the first site visit, then match to current stock or factory order. We are an independent service provider with no affiliation to Boral; we source through the same distributor network available to any licensed contractor, which keeps our quotes honest and our lead times predictable.

Signs Your Boral Fence Installation Is Failing

• Posts leaning at the base, especially after rain. In Irvine’s clay-heavy soils, particularly in the Portola Springs and Orchard Hills areas where cut-and-fill grading is common, Boral posts set without proper drainage aggregate heave and tilt. The composite or PVC board itself is fine; the failure is below grade.
• Boards cracking at rail attachment points. Boral’s poly-ash and PVC boards expand and contract with temperature swings. When installers over-tighten fasteners or skip the slotted rail holes, stress concentrates at the screw line and splits the board face within two to four years.
• Gate sagging or latch misalignment. Boral gates are heavy; the 6-foot privacy style runs 45-55 pounds per panel. Without a properly tensioned diagonal brace or adequate post depth (30″ minimum in Irvine’s seismic zone), the gate frame racks and the latch plate no longer meets the strike.
• Surface chalking or color shift. Boral’s factory finish holds well, but south- and west-facing exposures in Turtle Rock or University Park can show UV degradation after seven to ten years. This is cosmetic, but HOA boards in Irvine don’t treat it that way.
• Rail ends pulling from posts. The Boral rail-to-post connection relies on a bracket or pocket system that needs precise alignment. Settling, seismic movement, or original install without structural screws causes the rail to withdraw and the fence line to bow.

Before

After

Replacement Cost & What’s Included

What drives the range: site access (narrow side yards in older Irvine tracts add labor), footing condition (concrete removal runs $8-$12 per linear foot), and whether we match existing Boral color or you’re open to current stock shades. Every quote is a flat price with written scope; under Clause 1 of the Haven Standard, that number does not change unless you sign a change order. Our 365-Day Done Right Promise covers the installation, and we pull permits when Irvine requires them, which is standard for any fence over 6 feet or within required setbacks.

DIY or Call Us?

There’s a short list an owner can safely check: confirm whether your fence is actually Boral (look for the stamp or label), measure the failing section in linear feet, and photograph the post base for footing condition. What goes wrong fast: digging near unmarked utilities in Irvine’s dense utility corridors, setting posts without proper depth or drainage, and attempting to tension gate hardware without knowing the load. Boral boards are not light, and a full panel requires two people minimum to handle without twisting the rail clips. We carry the post-hole auger, the laser level, and the specific fasteners on every truck. Call (657) 227-2502 and we’ll schedule a site visit, deliver a written price, and typically start within a week.

FAQs