Cambridge Pavers Driveway & Pavers Nationwide

Cambridge Pavers Driveway & Pavers: The Irvine Owner’s Guide

We stock and install Cambridge Pavers-compatible driveway and paver systems in Irvine, with typical installed replacement costs running $7,000-$18,000 for paver driveway work and $3,500-$11,000 for paver patio installations depending on substrate condition and pattern complexity. Most Cambridge Pavers material inquiries can be matched to existing series within a single visit, and we carry common repair components for settling, edge restraint failure, and joint sand loss on our trucks. Most homeowners notice the problem first as a wobble underfoot, a visible dip collecting water after Irvine’s brief winter rains, or weeds pushing through gaps that used to be tight.

Call (657) 227-2502

Which Cambridge Pavers Models This Applies To

Cambridge Pavers organizes its residential line into distinct series, and the part or repair approach depends on which you have. The ArmorTec line, their most common Irvine installation, uses a proprietary surface layer that changes how we approach resurfacing versus full replacement. The Renaissance and Sherwood series use different edge restraint profiles, 8mm versus 6mm, which means the aluminum or PVC edging we order has to match or the perimeter will fail again in two seasons. To identify your series, look for the stamped logo on the paver edge or check your original installation paperwork for the Cambridge color code, typically a four-digit number.

We’re an independent service provider, not affiliated with Cambridge Pavers, so we source both OEM-compatible materials and quality equivalents from Belgard and Techo-Bloc when the original series has been discontinued. The aftermarket decision usually comes down to whether your existing pavers are still in production. If Cambridge has sunset your color, we match the closest current shade and document the variance in writing before ordering, so you’re not surprised by a two-tone driveway.

Signs Your Cambridge Pavers Driveway & Pavers Is Failing

• Sinking or tilting pavers in high-traffic zones. The bedding layer beneath has washed out or compacted unevenly, often where Irvine’s clay-heavy subsoil expands and contracts with seasonal moisture changes. We see this most often near garage aprons and at the bottom of sloped driveways where water concentrates.
• Weeds or moss growing between joints. The polymeric sand has degraded or was never properly installed, leaving voids that collect organic material. In Irvine’s mild winters, this accelerates once it starts.
• Pavers that sound hollow when tapped. The bedding sand has migrated, creating a void between paver and base. This progresses to cracking under vehicle load, especially on driveways built before 2015 when base-depth standards were less consistent in Orange County.
• Edge restraints pulling away from the perimeter. The spikes have corroded or the PVC has warped in summer heat, allowing the field to spread. This is the failure that turns a small repair into a full re-lay if it’s ignored through a rainy season.
• Surface spalling or color loss on ArmorTec finishes. The protective layer has worn through, usually from pressure washing at too narrow a fan angle or from de-icing salts tracked in from mountain trips. Once the ArmorTec layer is compromised, the underlying concrete absorbs stains differently.

Before

After

Replacement Cost & What’s Included

For Cambridge Pavers driveway work in Irvine, installed replacement runs $7,000-$18,000 depending on square footage, base reconstruction needs, and whether we match existing or switch series. Paver patio replacement falls at $3,500-$11,000. Driveway sealing, which we recommend every 3-4 years in Irvine’s UV exposure, costs $250-$700.

What drives the range: excavation depth if the base has failed, disposal of the existing field, and whether your HOA requires a specific pattern or color match. Our quotes itemize each line, paver cost separate from labor separate from base materials, so you see where the money goes. Under Clause 1 of the Haven Standard, that written price is delivered before any work starts. The 365-Day Done Right Promise covers the installation, and every visit includes a documented photo record of substrate condition, base prep, and finished grade, included as standard.

DIY or Call Us?

There’s safe inspection and then there’s work that goes wrong fast. An owner can check for loose pavers by hand, photograph the edge restraint condition, and measure the affected area for a phone discussion. What we don’t recommend: lifting multiple pavers without understanding the base layer, attempting to re-level with bagged sand from a hardware store, or pressure washing joint sand out without knowing how to replace it properly. The base on a Cambridge Pavers installation is engineered aggregate, not play sand, and the compaction requirement is specific.

We’ve been called to Irvine jobs where a weekend repair turned into a full replacement because the bedding layer was disturbed and never recompacted. Measure twice, build it once, write it down. For a written estimate that includes the actual parts and labor your project needs, call us at (657) 227-2502.

FAQs