Tamko Fence Installation Nationwide

Tamko Fence Installation: The Irvine Owner’s Guide

We stock and install Tamko-compatible fencing systems in Irvine, with most residential vinyl fence installations running $3,500-$9,000 for a complete, properly permitted job. Typical lead time is one to two weeks from signed quote to first post, though we keep common Tamko post caps, rail brackets, and hardware in our warehouse for faster repairs. Most Irvine homeowners discover their fence needs attention when posts lean after winter rains, pickets warp in the inland heat, or HOA inspection notices arrive citing height or finish violations.

Call (657) 227-2502

Which Tamko Models This Applies To

Tamko’s residential fence line centers on the EverGrain composite fencing system and the Tamko Building Products vinyl fence program, both distributed through select dealers in Southern California. The EverGrain line uses a wood-plastic composite board with a hidden fastener system; the vinyl program uses routed posts with snap-in rails in heights from 4 to 6 feet. To identify your system, check the post cap for a Tamko stamp or measure the wall thickness of the post: EverGrain posts are 5×5 inches with a 0.150-inch wall, while standard vinyl posts run 5×5 with a 0.135-inch wall. The rail bracket spacing also differs: EverGrain uses 6-inch centers, vinyl uses 8-inch.

We source OEM Tamko components where available, but we also stock quality aftermarket equivalents from Fortress and CertainTeed that match Tamko profiles and carry comparable fade warranties. In Irvine’s climate, the aftermarket vinyl often outperforms OEM on UV resistance because the formulations are newer. We document the origin of every part on your written quote so you know what you’re getting before we order.

Signs Your Tamko Fence Installation Is Failing

• Posts lean or wobble at the base. In Irvine, this usually means the concrete footing cracked during a dry spell or the post wasn’t set below the frost line (12 inches minimum per local code, though we typically go 18 inches for stability in sandy Irvine soils).
• Picketing or boards show chalking, fading, or surface cracking. Tamko’s original vinyl formulations from before 2018 are prone to UV degradation in inland Orange County sun; the surface oxidizes and the color washes out, especially on south-facing exposures near the Spectrum.
• Rails pull out of posts or sag between supports. This happens when the rail bracket’s internal spline wears down or the post routing enlarges from thermal expansion cycles, which are extreme here: 50°F winter mornings to 95°F summer afternoons.
• Gates drag, bind, or won’t latch. The gate frame is a parallelogram waiting to happen; once the diagonal brace loosens or the hinge post settles an eighth of an inch, the geometry fails and the latch misses the striker plate.
• HOA flags the fence for height, color, or material non-compliance. Irvine’s master-planned communities, especially Woodbridge and Northwood, enforce strict design guidelines. A fence that was compliant when installed may no longer match amended standards, or a previous owner’s DIY repair used mismatched materials.

Before

After

Replacement Cost & What’s Included

For a complete Tamko vinyl fence installation in Irvine, expect $3,500-$9,000 depending on linear footage, terrain, and whether we’re removing an existing fence. Here’s how that breaks:

• Materials: $18-$32 per linear foot for Tamko or equivalent vinyl picket fencing, including posts, rails, pickets, caps, and stainless steel fasteners
• Removal and disposal: $3-$6 per linear foot for existing fence tear-out
• Concrete and footing work: $45-$85 per post in standard soils; more in hillside or fill areas common near Turtle Rock
• Permit and inspection: $250-$450 through the City of Irvine, which we pull and schedule
• Gate hardware upgrade: $180-$350 per gate for heavy-duty adjustable hinges and latches

Every quote is a flat written price with a written scope. Under Clause 1 of the Haven Standard, that price doesn’t change unless you sign a change order. Our 365-Day Done Right Promise covers workmanship; manufacturer defects are handled through the material warranty, which we register for you.

DIY or Call Us?

There’s safe checking, and then there’s the part where most homeowners wish they’d called.

You can verify whether a post is loose by rocking it by hand, and you can sight down the fence line to spot sagging rails. But setting posts in concrete requires knowing the local amendment to the California Building Code for fence depth in expansive soils, and pulling a permit without a C-13 Fencing Contractor license isn’t an option in Irvine. We’ve replaced too many DIY jobs where the post holes were too shallow, the concrete was bag-mix that never cured properly in the dry heat, or the homeowner hit a sprinkler line they didn’t know was there.

One honest note: vinyl fence rails store significant spring tension when they’re flexed into routed posts. A rail snapping loose can split a knuckle or launch a fastener. We carry the clamps and spreader bars to control that energy. If you’re unsure, call (657) 227-2502 and we’ll walk through what you’re seeing. Estimates are free, and we bring a photo record so you can see what we found without climbing around yourself.

FAQs